Lynx EVO stereomicroscope - Revision history

Karolis: /* Remote access */ removed LogMeIn (not installed on PC)

2022-05-03T11:04:45Z

Remote access: removed LogMeIn (not installed on PC)

← Older revision		Revision as of 11:04, 3 May 2022
Line 35:		Line 35:
	== Remote access ==		== Remote access ==
	* TeamViewer: LYNX-PC		* TeamViewer: LYNX-PC
	* LogMeIn: ~~ELINE~~		<!-- * LogMeIn: Lynx -->
	[[Category:Characterization]]		[[Category:Characterization]]

Karolis: /* Remote access */

2022-05-03T11:04:17Z

Remote access

← Older revision		Revision as of 11:04, 3 May 2022
Line 33:		Line 33:
	;Where's the PC screen? I want to save an image!		;Where's the PC screen? I want to save an image!
	:The monitor is shared between the microscope and the bonder. Press <code>Scroll Lock, Scroll Lock, Enter</code> on the keyboard.		:The monitor is shared between the microscope and the bonder. Press <code>Scroll Lock, Scroll Lock, Enter</code> on the keyboard.
			== Remote access ==
			* TeamViewer: LYNX-PC
			* LogMeIn: ELINE
			[[Category:Characterization]]

Karolis: clarified location

2022-04-10T12:04:40Z

clarified location

← Older revision		Revision as of 12:04, 10 April 2022
Line 5:		Line 5:
	\|company = Vision Engineering		\|company = Vision Engineering
	\|description = Stereomicroscope		\|description = Stereomicroscope
	\|location = 03.1.111		\|location = 1st floor lab (03.1.111)
	\|primary = Karolis		\|primary = Karolis
	}}		}}

Karolis at 07:26, 7 April 2022

2022-04-07T07:26:57Z

← Older revision		Revision as of 07:26, 7 April 2022
Line 9:		Line 9:
	}}		}}
	Lynx EVO is a special microscope that gives sense of depth and has a large peripheral viewing angle due to its eyepiece-less design.		Lynx EVO is a special microscope that gives sense of depth and has a large peripheral viewing angle due to its eyepiece-less design.
	It is mostly used to check your work after bonding and save a reference image.		It is mostly used to check your work after bonding and to save a reference image.

	The Lynx EVO shares the computer screen with the [[FS bonder]].		The Lynx EVO shares the computer screen with the [[FS bonder]].
	The source PC can be switched by pressing <code>Scroll Lock, Scroll Lock, Enter</code> on the keyboard.		The source PC can be switched by pressing <code>Scroll Lock, Scroll Lock, Enter</code> on the keyboard.
			== Usage instructions ==
			# Turn on the power supply on the left side of the microscope.
			# Turn the knob on the power supply clockwise to increase the light intensity. 20% (one increment) of the scale is a good starting point.
			# Place your sample under the microscope and check if you can see it.
			# Adjust the focus by turning the double knob on the side of the microscope. The larger wheel adjusts the working distance coarsely, and the smaller does finer adjustments. You should be able to see your sample through the big eyepiece.
			#: If you cannot reach a reasonable focus, maybe your sample is too low/high? Even though it is possible to move the whole microscope, first try changing the vertical position of your sample. Try putting it on a small box if you had it on the workbench, and vice-versa.
			# Adjust the zoom by turning the other knob on the side of the microscope.
			# If you want to take a picture, use the uEye software on the Lynx PC.
			#: Note that the microscope shares the screen with the bonder. You can switch between computers by pressing <code>Scroll Lock, Scroll Lock, Enter</code> on the keyboard.
			# When you are done:
			#* Close the uEye software
			#* Zoom all the way out
			#* Turn the light intensity down
			#* Turn off the power supply
			#* If you used a red plastic box, move it out of the way
	== Troubleshooting ==		== Troubleshooting ==
	;I can't get a responsive image in the software!		;I can't get a responsive image in the software!

Karolis: Created page with "{{Infobox tool |image = Tools Lynx EVO.jpg |toolfullname = Lynx EVO |website = https://www.visioneng.us/products/stereo-microscopes/lynx-evo/ |company = Vision Engineering |de..."

2022-04-07T07:12:41Z

Created page with "{{Infobox tool |image = Tools Lynx EVO.jpg |toolfullname = Lynx EVO |website = https://www.visioneng.us/products/stereo-microscopes/lynx-evo/ |company = Vision Engineering |de..."

New page

{{Infobox tool
|image = Tools Lynx EVO.jpg
|toolfullname = Lynx EVO
|website = https://www.visioneng.us/products/stereo-microscopes/lynx-evo/
|company = Vision Engineering
|description = Stereomicroscope
|location = 03.1.111
|primary = Karolis
}}
Lynx EVO is a special microscope that gives sense of depth and has a large peripheral viewing angle due to its eyepiece-less design.
It is mostly used to check your work after bonding and save a reference image.

The Lynx EVO shares the computer screen with the [[FS bonder]].
The source PC can be switched by pressing <code>Scroll Lock, Scroll Lock, Enter</code> on the keyboard.

== Troubleshooting ==
;I can't get a responsive image in the software!
:First close the uEye software. Make sure the Lynx EVO power supply is on. Then open the uEye software and press the "Play" button.
;Where's the PC screen? I want to save an image!
:The monitor is shared between the microscope and the bonder. Press <code>Scroll Lock, Scroll Lock, Enter</code> on the keyboard.